Professional Waterproofers

Description
ShaliUrethane BTDis UV resistant, high performance, water based, cold applied, single component elastomeric in-situ liquid membrane for waterproofing.ShaliUrethane BTDforms a seamless monolithic membrane, which can be applied on moist surface not exceeding 5%.

It conforms to ASTM C 836 and ASTM D 6083.

Use Horizontal / Vertical grade of ShaliUrethane BTDfor horizontal / vertical application respectively

Application
•Roof / Terraces, including corrugated roof.
•Terrace garden.
•Podium.
•Planter boxes.Advantages
•Can be applied on moist surface also.
•Excellent water vapour barrier.
•High Crack Bridging.
•Monolithic / seamless in-situ Membrane.
•Excellent adhesion to concrete.
•Excellent elongation and very good low temperature flexibility.

Application Methodology
Surface Preparation
•Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application.
•Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete : Cement : Sand (1 : 2 : 5).
•Provide 75 mm x 75 mm coving made out of PMC mortar as above, using ShaliSBR Latex as bond coat.
•Ensure that the moisture content in the prepared surface does not exceed 5%.

Material Preparation
•Stir ShaliUrethane  BTDby a slow speed mixture (approx. 400 rpm) fitted with a suitable mixing paddle to ensure a homogenous mix
•Skin formation may happen on the top of material during humid condition. In that event, cut skin from the periphery of the container and remove it and then stir it as mentioned above. BTDby a slow speed mixture (approx. 400 rpm) fitted with a suitable mixing paddle to ensure a homogenous mix.
•After stirring, wait for the product to settle in order to let entrapped air escape.

Protection of Waterproofing
•Spread separation layer of 200 gsm geo-textile, ShaliGeoText 200 with overlap of 50 mm in both directions on fully cured waterproofed surface before laying protection screed.
•Protect the surface with 50 mm PCC admixed with integral waterproofing compound, ShaliPlast LW+ 200 ml / bag of cement with galvanised chicken wire mesh ensuring a gradient of 1 : 100 towards drain

Health & Safety
• Avoid contact withskin / eyes, and avoid swallowing.
• Ensure adequate ventilation and avoid inhalation of vapour.
• Wear suitable protective clothing, gloves and eye protection.
• In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water.Do not use solvent to clean the contacted area.
• In case of eye contact, wash with plenty of clean water and seek medical advice.
• If swallowed, seek medical attention immediately. Do not induce vomiting.

We are engaged in offering Waterproof Coatings to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering Waterproofing For Toilets to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering App Waterproofing Membrane to our clients. Our range of all products is widely appreciated by our clients.

Offering you a complete choice of products which include shaliurethane btd water resistant liquid membranes, shalicryl lm hi, waterproofing for toilets, liquid waterproofing coating, app waterproofing membrane and shalicem ewp elastomeric waterproofing coating.

Offering you a complete choice of products which include shaliurethane btd water resistant liquid membranes, shalicryl lm hi, waterproofing for toilets, liquid waterproofing coating, app waterproofing membrane and shalicem ewp elastomeric waterproofing coating.

Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. 

“Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc.

 “Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. 

We are engaged in offering Shalicryl Lm Hi to our clients. Our range of all products is widely appreciated by our clients.

Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification.

We are engaged in offering Liquid Waterproofing Coating to our clients. Our range of all products is widely appreciated by our clients.

TamPur 130 is part of our new ECO range and is a single component, high foaming, semi flexible water reactive polyurethane injection resin. TamPur 130 (ECO Range) has been formulated to effectively seal cracks and joints in construction that exhibit a degree of movement, forming a semi flexible, closed cell foam sealant. The reaction speed of the resin can be adjusted using TamKat 130 providing flexibility on the job site. TamPur 130 (ECO Range) is phthalate free and environmentally friendly.

Description
ShaliCem EWP is ready to use two component coating based on cement with carefully graded aggregates in combination with selected admixtures and synthetic resins. ShaliCem EWP is highly recommended to waterproof concrete. 

Application
• All masonry surfaces both inside and outside.
• Basements, tunnels, machinery pits, cisterns, reservoirs.
• Roofs and Terraces.
• Swimming pools, Toilets, water retaining structures.

Advantages
• UV Resistant.
• Exhibits good water proofing character.
• High Flexibility.

Application Methodology
• Ensure that structure is sound and free from dirt, soil, oil release agents, laitance and any other foreign materials which may impair the bond, penetration and/ or the overall performance of ShaliCem EWP.
• Chemically remove any efflorescence, form oil, mould etc.
• Repair any cracks, honeycombed pockets or holes by Shalimar Dam-It or PlastiSeal.
• Ensure to dampen walls for an hour before application and keep damp allowing moisture to soak in. Wet dense concrete at least twice, not less than 30 minutes apart. Surface must be damp during application. Do not allow standing water.
• Prime the area with slurry by mixing one part of ShaliCrete E with two parts of neat cement i.e. in the ratio 1 : 2.
• Add Component B into a suitable container containing and thereupon, add Component A slowly whilst mixing thoroughly mix it preferably in a Jiffy Mixer.
• Crush any globules formed to make uniform paste and continue mixing.
• Apply ShaliCem EWP on clean and dampen surface with stiff fibre brush. Scrub well into the damp wall filling all pores and finish with final stroke in one direction. Keep a wet edge.
• Apply second coat when the first coat is touch dry.
• Allow to dry for 24 hr before moist curing. Do not apply water through a hose or pressurized nozzle.
• Light spray of water may be required between coats in hot/ dry climates.
• Apply 15 – 25 mm PCC to protect the treated surface, if traffic is expected on such surface.
• When surface becomes hard enough, fog spray with clean water keeping wall damp for 3 days. Hotter the weather, more critical the curing. Light spraying of water is recommended more frequently and for several days. 

Health & Safety
• Use mask, nose cover and hand gloves during application.
• Clean hands with soap water after application.
• Avoid contact with skin / eyes. In case of unlikely contact with eyes, rinse immediately with plenty of clean water, then cleanse with soap and lukewarm water and seek medical advice. Do not use solvent to clean the contacted area.
• Prevent swallowing. In case of unlikely swallowing, seek medical attention immediately. Do not induce vomiting. 

ShaliSeal® PS PG is two component, polysulphide polymer based, UV resistant, flexible tear resistant, rubbery, self-leveling, pourable, non-staining sealant, which adheres to most of building materials like cementitious substrates, aluminum, glass, wood, mild steel, etc. It cures at ambient temperature, has excellent recovery characteristics after extended period of compression / elongation with outstanding resistance to most chemicals,weather conditions, aging and shrinkage.

 “Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification. Moreover, we follow moral business policies and crystal pure transparency in all our transactions to keep healthy relations with the customers. 

ShaliGrout® 73 is a high-strength, non-metallic, non-shrink grout designed for precision grouting and general construction applications. It can be mixed to a fluid, flowable, or plastic consistency requiring only the addition of clean water. It is formulated as a natural aggregate system with a shrinkage- compensating binder and is highly flowable without sacrificing strength or performance capabilities. It can also be used for anchoring a wide range of fixings. These include masts, anchor bolts and fence posts

Sika® Backer Rod PH is closed-cell, extruded polyethelene foam backing rod, available in diferent diam

ShaliGrout® IP is a plasticized and non-shrink cement / mortar admixture for pressure / injection grouting. By introducing into the cementitious grout, it reduces water cement ratio and facilitates volume expansion without segregation or bleeding. It may also be used to get water tight dense structures. It complies with BS 8110 part 1, 1985, section 8.9.4.6. 

ShaliSeal® PS GG is two component, polysulphide polymer based, UV resistant, flexible, tear resistant, rubbery, self-leveling, gun grade, non-staining sealant, which adheres to most of building materials like cementitious substrates, aluminum, glass, wood, mild steel, etc. ShaliSeal® PS GG cures at ambient temperature, has excellent recovery characteristics after extended period of compression / elongation with outstanding resistance to most chemicals, weather conditions, aging and shrinkage. It conforms to BS 5212:1990 Part I - Type F & Type FB (Flame and Fuel Resistant), IS 12118 Part 1 - 1987, BS:4254 and ASTM C 92

Two component, cementitious acrylic polymer based high performance water proofing coating. It offers seamless flexible crack bridging

 “Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification. Moreover, we follow moral business policies and crystal pure transparency in all our transactions to keep healthy relations with the customers. 

“Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification.

“Professional Waterproofers" is Wholesaler, Trader, Distributor of Waterproofing Chemical , Waterproofing Service, Waterproof Coating, Polysulphide Sealant, Bituminous Primer etc. We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification.